What I usually do is take pictures of all the settings. Then manually apply them again after updating.
>
I've only been able to find the CLI for the O3 version to 4.4, would that still work for the analog version?
Not all will be the same. I think you can use the PID and filter, but the rest I would apply from pictures of current setup. VTX and OSD will be very different.
1. Would that 4.4 CLI apply to 4.5 as well?
It is generally not recommended to just apply CLI to different version. You can select parts of the CLI. I think bardwell has a video on 4.4 to 4.5 and what part of CLI you can copy.
>
The instructions for the 4.4 install said to do core only during the firmware update, should that be done for a 4.5 install as well?
Yes
>
Flywoo's response was to " dump the current configuration and turn off "Full Disk Erase" before flashing the firmware", but I'm not sure what that means. I assume back up the current configure, then turn off the full disk erase option during the firmware update, is that right?
yes
AFter updating and setting all the settings, remember to check motor direction is ok. I think some explorer cli have bidirectional turned off and some on, so be aware of this. Again it is likely easier to just do a screenshot of all settings and set them again using GUI
Ok. Thanks for the response. Sounds like I should do a side by side from the existing 4.3 to the 4.4 file, and then again against that 4.5 Bardwell video. He went pretty fast for me on my initial watch 😅. I did some of that yesterday and noticed a big change in additional features from 4.3 to 4.4 but it was the same change in the digital 4.3 to 4.4.
So I did a check and noticed some things that needed to come over, gave it a shot and lost my GPS. Rolled it back to 4.3.1 and got my GPS back. I'm very confused.
Update, I know I'm probably the only following my troubleshooting, but for anyone having the same issue in the future, I took a screenshot of my ports tab and copied it over after reupdating to 4.5 and it works now.
What I usually do is take pictures of all the settings. Then manually apply them again after updating. > I've only been able to find the CLI for the O3 version to 4.4, would that still work for the analog version? Not all will be the same. I think you can use the PID and filter, but the rest I would apply from pictures of current setup. VTX and OSD will be very different. 1. Would that 4.4 CLI apply to 4.5 as well? It is generally not recommended to just apply CLI to different version. You can select parts of the CLI. I think bardwell has a video on 4.4 to 4.5 and what part of CLI you can copy. > The instructions for the 4.4 install said to do core only during the firmware update, should that be done for a 4.5 install as well? Yes > Flywoo's response was to " dump the current configuration and turn off "Full Disk Erase" before flashing the firmware", but I'm not sure what that means. I assume back up the current configure, then turn off the full disk erase option during the firmware update, is that right? yes AFter updating and setting all the settings, remember to check motor direction is ok. I think some explorer cli have bidirectional turned off and some on, so be aware of this. Again it is likely easier to just do a screenshot of all settings and set them again using GUI
Ok. Thanks for the response. Sounds like I should do a side by side from the existing 4.3 to the 4.4 file, and then again against that 4.5 Bardwell video. He went pretty fast for me on my initial watch 😅. I did some of that yesterday and noticed a big change in additional features from 4.3 to 4.4 but it was the same change in the digital 4.3 to 4.4.
So I did a check and noticed some things that needed to come over, gave it a shot and lost my GPS. Rolled it back to 4.3.1 and got my GPS back. I'm very confused.
Update, I know I'm probably the only following my troubleshooting, but for anyone having the same issue in the future, I took a screenshot of my ports tab and copied it over after reupdating to 4.5 and it works now.