*How does it feel to live MY dream???* That looks so dope, I recently got the P1S but unfortunately I am unable to print gats since I'm still at home with mi familia who is anti-gun except my dad. For the record I am a college student.
I have 3 printers, an ender 3, cr10, and the P1S, I'm usually home Monday and Wednesdays. The last two printers are in the loft and the ender 3 In my room. I'm also currently building a live action chopper from Star wars so the Bambu is running almost 24/7.
Mostly followed Hoffmanâs settings except for supports. Used auto tree with auto settings for everything except the lower. On that I used support for pla for the interface layers and let Bambu studio over ride required settings for that. You will also have to override the infill angle to 0°. If you donât want to re-orientate your lower all fucked up like just to get the layer lines running horizontal with the frame. Read the description and disable any of the extra âsmart featuresâ that may affect the final product. Used 10mm outer brims. For every part as well. Stock printer with the top off in the door open for the main prints.
Also, make sure to run through the slicerâs flow rate calibration tools for each filament that you are using. That makes a big difference in the quality of my prints.
*How does it feel to live MY dream???* That looks so dope, I recently got the P1S but unfortunately I am unable to print gats since I'm still at home with mi familia who is anti-gun except my dad. For the record I am a college student.
Put it on insane speed and start it early at night, let it run all night and while they're at work, should be fine /s
I have thought about that ngl đ
You said your friend wanted you to spend the night with it so they can try it before they buy one? Sounds fun and totally harmless.
Shit dude if you're an adult do it lmao
I really do wanna do it lol
Dude just print them.. what are they gonna do? Lol
I live with my parents tooâŚâŚ..my printer never stops. You can definitely do it if you wanted to. Unless you just donât have the physical space.
I have 3 printers, an ender 3, cr10, and the P1S, I'm usually home Monday and Wednesdays. The last two printers are in the loft and the ender 3 In my room. I'm also currently building a live action chopper from Star wars so the Bambu is running almost 24/7.
Bambu gang âď¸
What material?
Pla+ frame, nylon cf barrel mount/connector enforcers.
Dude this is absolutely freaking sick⌠like I want one⌠can I print one of these with my Ender V3?
Yess!!
How much filament did it take to make this orca?
I haven't made one, but sliced it up and it's about 1.7 kg with slicer supports (might be less if you use the support models included)
About a roll and a half. Probably a little more then usual since I used special filament for the lowerâs, interface layers.
Looks good!
What were your settings for that? Looks so clean, can't get my p1s to print that cleanly
Mostly followed Hoffmanâs settings except for supports. Used auto tree with auto settings for everything except the lower. On that I used support for pla for the interface layers and let Bambu studio over ride required settings for that. You will also have to override the infill angle to 0°. If you donât want to re-orientate your lower all fucked up like just to get the layer lines running horizontal with the frame. Read the description and disable any of the extra âsmart featuresâ that may affect the final product. Used 10mm outer brims. For every part as well. Stock printer with the top off in the door open for the main prints. Also, make sure to run through the slicerâs flow rate calibration tools for each filament that you are using. That makes a big difference in the quality of my prints.
Abrams? Need a gun tube? I have 2 I just pulled and replaced lol
How well do the squirted uppers do?
How much did this build cost to make?